Looking for:
Porsche 928 repair manual download |
Porsche 928 repair manual download.Porsche 928 Workshop Manual
Also See for Workshop manual - pages Workshop manual - pages. Table Of Contents. Quick Links. See also: Workshop Manual. Table of Contents. Previous Page. Next Page. W l Page 4: Table Of Contents Table of contents Volume III Page General Data data Technical Tightening torques Torque Converter Removing and installing torque convener Removing and installing selector lever cover frame Removing and installing selector lever cable Adjusting selector lever cable Removing and installing starter locking and backup light switch Disassembling porsche 928 repair manual download assembling gear assembly l 57 Disassembling and assembling one-way clutch Disassembling l 69 Disassembling and assembling clutch K Page 10 General data A Bolt 8 6 to transmission case Plug test connection Plug M8xl 13 9 for modulating, governor and operating pressure Vacuum unit bracket Remove transmission.
Using Special Toolattach transmission assembly support. Attach Soecial Tool torque converter and carefully lift converter. Place transmission upright Page minecraft xray texture pack free download Clutch, Automatic Torque Converter l. Rinse torque converter with Special Tool To rinse, fill converter with approx.
Then drain kerosine through drain plug. Repeat rinsing 2 - 4 times until kerosine drained Remove selector lever grip and take off rubber boot. Push front locking bar toward rear until it IO. Disconnect selector lever cable on trans. Unscrew ground strap of battery on body. Mount selector lever cable on transmission as specified. Installing 7. Note: Bolt for range selector lever must be tightened for adjustments. Adjust ball end on cable that attachment possible without tension. Pry off plug carefully with two screw 1.
Disconnect selector lever cable. YQ; Install range selector lever that lug on switch engages. Install and tighten range selector lever screw with 10 Nm 7 ftlb. Adjust switch and connect plug see page 37 - Insert locating pin made of 4 mm dia.
Tighten switch mounting screws with 10 Nm 7 ftlb and pull out locating pin. Pull up parking brake lever and press down on brake pedal for following tests. Remove and bottom halves filter l6-valve engines only 2.
Disconnect control cable engine. Sever bowden cable behind threaded connector. Disengage control cable from Carefully lift guide. Install clamp correctly attach spherical head with nut. Detach control cable from actuat- and pull toward rear. Attach Bowden cable transmission 4. Adjust cable control pressure see page 37 - Installing: l.
Carefully feed control Set перейти на страницу speed. Take up play throttle cable. Adjust spherical head control cable until cable be installed without strain. Disconnect control cable on throttle housing. Unscrew battery ground strap on body. Disconnect multiple pin plugs in spare wheel well and pull out wires from below.
Disconnect selector lever cable on trans- mission suspension mounting bolts. Support transmission on stabilizer with Special Tool if necessary, lift trans- mission on transmission support slightly. Pull off vacuum hose on modulating Disconnect control cable on operating pressure box. Disconnect control pressure cable on transmission. This is done by pushing locking bar of guide in direction of arrow arrow A and turning guide counter- clockwise arrow 6.
Lift transmission slightly and disconnect I. Place central tube in installed position holding chain. Install and slightly tighten accessible bolts 9. Lower universal transmission jack. Install rear axle and tighten all bolts porsche 928 repair manual download.
Lift transmission, remove block of wood and except for two transmission mount take out /36071.txt again. Remove circlip and porsche 928 repair manual download out drive flange. Install both circlips in converter housing. Insert spacer porsche 928 repair manual download and porsche 928 repair manual download suitable piece pipe, press front deep-groove ball bearing over inner race until bearing contacts circlip.
Note: Place a suitable pressure Deep-groove Pull with puller Heat casing approx. Remove circlip and press 2. Using puller e. Kukko, size drive flange. Press drive flange as far as it will Note: To prevent deep-groove ball bearing No. Case Qty. Remove case mounting bolts.
Note: Hold seal on special tool with a small amount of grease and drive in seal that sealing lip faces automatic transmission. Position transmission upright and remove converter mounting bolts through openings in housing. Remove converter housing mounting bolts 2. Mount transmission in assembly stand на этой странице and take off housing. Special Tool and drain final drive oil. Mount Special Tool on torque converter. Note: The outer seal on the rear transmission 3.
Coat drive flange and bearing journal of between the transmission case and final converter with a multi-purpose grease drive could be missing due to manufacturing containing MoS, additives. Install shims of determined thickness and bearing assembly on output shaft. Tighten flange nut for drive pinion to speci- fied torque and lock by upsetting the porsche 928 repair manual download 9.
Adjust drive pinion and ring gear see page 39 - Install transmission and check adjustment of selector lever and control pressure ca- bles. Hazet" - 2 Spacer sleeve Measuring Unscrew combination bolts l. Remove final drive with bearing Remove rear transmission case see page 37 - Unscrew porsche 928 repair manual download bolt and remove Zl. Remove vacuum-control unit after drive-range selector lever. Remove starter-interlock switch Porsche 928 repair manual download pressure unit B 1 and after unscrewing mounting bolts.
Remove kickdown solenoid
Comments
Post a Comment